30 Watch Winder with Fingerprint Lock and Storage Drawer (Carbon)
- YOUR ENTIRE COLLECTION INSIDE: With 30 rotors and a large storage drawer you will be able to keep all your accessories in one place.
- FITS MOST WATCHES: Polyurethane watch holders fit any bracelet or strap sizes and can be used for men’s as well as women’s watches.
- FINGERPRINT LOCK allows you to prevent unwanted access.
- STUNNING APPEARANCE: Watch winder with a high-gloss finish and large display window will fit perfectly in any interior.
- UNIVERSAL COMPATIBILITY: The individually programmed rotors and 15 available winding programs meet all existing winding requirements.
- EASY USE & SETUP: The LCD display with touch control makes the setup process simple.
- INTERIOR BACKLIGHT : Your watch collection will look especially beautiful in the dark.
- PERFECT PRESENTATION: The watches come to rest at the same position after each winding cycle for a better display.
Notify me when this product is back in stock
Availability: Out of stock
30 Watch Winder with Fingerprint Lock
With 30 rotors and a large storage compartment, you’ll be able to keep your entire collection in one place. The watch winder needs as little as 21" x 11" on your desk or dresser.
- Soft polyurethane watch pillows;
- Exterior finish: High-gloss piano lacquer;
- Interior lining: Velvet;
- Maximum watch case diameter: 2.4 inches (60 mm);
- Individually programmed winder rotors;
- 3 winding directions;
- 15 winding programs;
- Turns-Per-Day range: 650 to 1950 TPD;
- Large storage drawer (W x L x H): 7.5" x 17.5" x 2.75" (18.5 cm x 45 cm x 7 cm);
- LED interior backlight;
- Motor-Stop option;
- Coordinated rotor stop position;
- LCD touch control panel with digital clock;
- Fingerprint lock;
- AC power adapter included (100-240V, 50-60Hz).
Watch winder description:
The watch winder features a Motor-Stop Option. When you open the door, the rotors stop automatically. This prevents possible breakdowns of the winding mechanism while installing or removing watches.
All the rotors stop at the same position after each winding cycle for a better display of your watch collection. The rest position is at an angle of approximately 60° to the vertical (the 2 o’clock position).
The rotors can be programmed to operate independently. You can set an individual program for each rotor depending on the watch model you are placing into it. The control panel allows you to disable the rotors you do not use.
The 15 winding programs provide compatibility with any watch models. You can choose the number of turns per day from 650 to 1950 TPD in combination with any rotation direction.
The LCD touchscreen display enables easy setup. Three rotation directions are available: clockwise, counterclockwise and bi-directional (mixed). In the mixed mode, the rotor rotates clockwise and counterclockwise alternately. An electronic controller counts every turn of the watch for supreme winding precision. The rotors are very quiet. You can hardly hear them spinning.
The watch holders fit men’s as well as women’s watches. You can use them for bracelets with a girth from 6.5” to 7.9” (16.5 to 20 cm). The watch holder is made of soft polyurethane and will never scratch your watch or bracelet.
The fingerprint lock allows you to prevent unwanted access to your watch collection. You can save up to 20 fingerprints. The lock setup is optional. If you do not want to use this option, the lock will open with any fingerprint.
What is an automatic watch winder?
A watch winder is a device with an electrical motor which will automatically wind your watch when you are not wearing it. Automatic watches have a limited power reserve, so if you stop wearing them and winding them up, they will run down in two or three days. The reserve depends on the watch brand and on movement (caliber) used.
When your timepiece stops, you must reset time and wind up your watch. If it has additional functions (like date, moon-phase display, perpetual calendar), resetting them may take a lot of time and require certain skills. With an automatic watch winder, you can keep your timepiece wound and ready to go!
Please note: If your watch doesn't wind itself from wrist motion, it cannot be wound by an automatic watch winder. Watch winders are not compatible with Seiko Kinetic Watches because their watch mechanism is different from the traditional one.
The watches shown in the pictures are not included.
Please note: Watch winding mode (winding direction and TPD setting) depends on your watch model. Please, check your owner's manual or contact your watch brand's customer service for detailed information.
You can also refer to our watch winding parameters table.
LCD Display with Touch Control
Watch Winder Programming
The watch winding mode (the winding direction and the Turns-Per-Day setting) depends on the watch model.
Please check the user manual of the watch or contact the customer service of your watch brand for detailed information.
Each rotor can be programmed independently.
1. Select a rotor to program. Use [◀] and [▶] buttons to select a setting target. The selected rotor will be shown in the Rotor Selection Section on the display.
2. Having selected a rotor to program, select the number of Turns-Per-Day (TPD) by pressing [+] and [–]. There are 5 TPD settings available: 650, 750, 850,1000 and 1950.
3. Select the winding direction for your watch by pressing [ROTATION DIRECTION].
4. Press [START/STOP]. The display will show [ON] in the Rotor Selection section and the selected rotor will start moving. If Motor-Stop option is enabled, the rotation will start after you close the door. PLEASE NOTE: The winding controller splits the programmed number of turns per day in 24 hours evenly. The rotors do not rotate continuously and stay motionless most of the time.
It is recommended to deactivate the rotors you do not use.
1. Press [◀] and [▶] several times to select a rotor.
2. Press [START/STOP]. The display will show [OFF] in the Rotor Selection Section and the selected rotor will not move until you reactivate it. Active rotors are always indicated by an underline under their numbers.
New Watch Mode
This mode is intended for winding new or stopped watches. To activate this mode, please proceed as follows:
1. Mount the watch and choose the rotor by pressing [◀] and [▶].
2. Set the required TPD and rotation direction by pressing [+], [–] and [ROTATION DIRECTION]. Then press [START/STOP] to activate the program (the display must show [ON] in the Rotor Selection Section).
3. Press and hold the TPD display area for 2 seconds.
The Turns-Per-Day display will show [ - - - - ] and the selected rotor will start moving. It will rotate the watch for 4 hours continuously. Then the rotor will rest for 8 hours and return to the programmed winding mode. If you have set a bi-directional mode, the rotor will rotate clockwise for 2 hours and counterclockwise for another 2 hours.
Press and hold [START/STOP] for 2 seconds until the control panel vibrates. Use [◀] to set the hour, [▶] button to set the minute and [START/STOP] to save the settings.
Press [LIGHT] to turn the interior light ON or OFF. The light can also be controlled by the red switch on the rear panel (optional).
To prevent the winding mechanism from breakdowns, it is recommended to put a watch into a rotor or take it out only when the rotor is stopped. If the Motor-Stop option is enabled,
all the rotors will stop once you open the door. To enable this option, flip the small black switch on the back panel to the ON position (optional).
PLEASE NOTE: The rotors will not rotate if the Motor-Stop option is enabled and the door stays open. Please keep the door of the watch winder closed for its proper operation.
1. If your watch allows for manual winding only, this watch winder will not be able to wind it. Watch winders are not compatible with Seiko Kinetic
Watches because their winding mechanism is different from the traditional automatic watch movement.
2. The watch winder can also be powered via the USB power plug (optional). A 5V 2A adapter with a micro-USB or USB-C plug required (not included). Do not use a USB power adapter and the original AC adapter at the same time. You can use USB-out port to charge a fingerprint lock (optional).
There are three ways to put a watch on the watch pillow depending on your wrist size:
The pillows are made of soft polyurethane and will not scratch your watch.
Leader Watch Winders is our own brand.
Since 2010, we have learned to create functional, attractive, and most importantly, reliable watch winders. Every year we launch new models. Each of them becomes a symbol of quality and convenience.
In order to minimize our production costs, we placed our manufacturing facilities in Guangzhou, China, where we also organized a design department in addition to the production premises.
Our major market outlets are the USA and Russia. We are planning to launch an online shop in Germany by the end of 2020 to supply Europe with our winders.
Apart from winder production, we upgrade safe boxes into safe storage units for your watch collection. Safe boxes are covered with faux and real leather and equipped with internal watch winding systems. Many safe boxes also have an alarm system.
In 2020, we are launching our new model 8030 for winding 30 watches simultaneously. Moreover, this model will have a separate rotor for each watch.
We are proud of our products and we hope you will enjoy using Leader Watch Winders!
|Maximum Watch Diameter||2.4" (60 mm)|
|Watch Winding Slots||30|
|Number of Rotors||30|
|Watch Holder Type||Polyurethane|
|Watches on Rotor||1|
|Watch Storage Compartment||Yes|
|Power Adapter||AC 100-240V 50-60Hz|
|Item Weight (lbs)||66.1|
|Item Length (inch)||21|
|Item Width (inch)||10.5|
|Item Height (inch)||32.5|